Tag: msd

MSD Performance: Black Blaster Coils for ’03-’16 Hemi

David Ayers Leave a comment
Use This Post Clip for Email

Direct-replacement Blaster Coils from MSD Performance possess superior winding ratios and materials to provide your 2003–2016 Hemi engine with legendary ignition performance while retaining the factory fit. Sold singly or as a set of eight, these coils offer improved high-RPM operation and easy installation thanks to a direct bolt-in design and plug-in interface with factory connectors.

Features

  • Patented winding design and materials.
  • Improved high-RPM performance.
  • Bolts into factory location and plugs into factory connectors.
  • Max. voltage: 36,000
  • Primary resistance: .403 ohms / secondary resistance: 14.5K ohms
  • Spark energy: 96 mJ / spark duration: 1,320 mS
  • Sold in singles or packs of 8.

MSD Performance Black Blaster Coils for Hemi

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.

MSD (2700): Atomic AirForce Manifold for 2014-2015 Chevrolet Corvette LT1

David Ayers Leave a comment
Use This Post Clip for Email

If you’re looking for bolt-on power and torque for your new LT1, the new Atomic AirForce intake manifold from MSD is the answer! This all-new polymer intake will increase the performance of stock and modified versions of the Direct-Injected LT1 engine.

MSD initiated the clean-sheet AirForce design by addressing the performance shortcomings of the OEM manifold. Through the use of Computational Fluid Dynamic modeling, MSD was able to optimize the plenum volume and improve runner layout. Unique bell-mouthed runner openings, optimum runner length, and minimal shrouding ensure maximum airflow and cylinder-to-cylinder balance.

The LT1 intake is a two-piece molded design that allows for porting and runner modification, while the polymer construction minimizes weight and heat absorption. MSD also made it easy to accommodate power adders by equipping the AirForce LT1 manifold with integral port fuel injection bosses at the base of each runner.

The AirForce LT1 intake accepts an OEM electronic throttle body as well as aftermarket electronic throttles up to 105 mm.

MSD Atomic 2700
MSD Atomic 2700

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.

MSD (2900): Atomic EFI Master Kit

David Ayers Leave a comment
Use This Post Clip for Email

The MSD 2900 is the complete kit for anyone planning to convert from a carburetor to Atomic EFI. You get the Throttle Body, Power Module (with Wide Band O2 sensor), Handheld Controller, and the Standard Fuel Kit for up to 525hp naturally aspirated (at the crank). The Atomic TBI is compatible with Boost/Nitrous!

  • Blow Through or Draw Through
  • 2 BAR MAP, up to 14psi
  • Timing Control (Retard per pound of boost)*
  • Alternate Air Fuel setting under boost
  • Includes a Nitrous Retard (It will retard timing when nitrous is active).

*The Atomic must be controlling ignition timing in order for the Boost/ nitrous timing retards to work.

MSD_2900
MSD_2900

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.

MSD (2950): Atomic LS2/LS3 EFI Kit

David Ayers Leave a comment
Use This Post Clip for Email

MSD is breaking new ground in electronic fuel injection with the next generation of Atomic EFI—the all-new Atomic LS system. Where the Atomic TBI consolidated electronics and sensors into the throttle body itself, the LS platform incorporates the electronics into the fuel rails of the system! There’s no bulky ECU to mount and, therefore, no wires to route to and from; it’s all on the engine, hidden in plain sight.

There’s no need for a PC, complicated software, or prior tuning experience. Simply bolt it on, plug it in, answer a few car-guy questions using the supplied handheld controller, and start the engine. The Atomic LS will begin learning and tuning your LS engine as soon as you fire it up. Advanced adjustments can be made to air/fuel targets, pump squirt, ignition timing. and much more. The self-tuning Atomic LS system will give you the performance and driveability you expect from your LS engine.

MSD has a variety of advanced programming features that are simple to navigate using the handheld programmer. These unique features allow you to get the most performance and benefits from your new Atomic EFI system.

MSD Atomic 2950
MSD Atomic 2950

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.

MSD: 2950 Atomic LS EFI Kit

David Ayers Leave a comment
Use This Post Clip for Email

MSD has made Atomic EFI the simple solution for your LS EFI needs. Start your installation by knowing that you’re getting everything you need for your crate engine. These kits are each designed for a specific engine and are supplied with Rail Assemblies, Handheld Controller, Power Module and Harness, Wide-Band 02 Sensor and Bung, -6 fittings for the fuel rails, and cross-over hose.

MSD 2950
MSD 2950

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.

MSD Completes Mallory Merger

David Ayers Leave a comment
Use This Post Clip for Email

mallory-msd-merger

One good M deserves another.

Following the January 2015 acquisition of ACCEL Performance Group (maker of Mallory Ignition, Mr. Gasket, Hays, QuickTime, and others) by MSD Performance, the MSDP Group completed the planned merger of the Mallory and MSD lines to create the top ignition company in the automotive aftermarket.

As of March 31, the Mallory product line will no longer be produced; all Mallory products will be manufactured exclusively under the MSD brand. MSD will, however, continue to produce and service Mallory distributor replacement parts such as points, rotors, caps, and more than one hundred other items. In addition, MSD will continue repairing Mallory products and honoring all original Mallory warranties. Retailers, installers, and customers should direct Mallory warranty inquiries to MSD’s toll-free number: (800) 246-0270.

Mallory and MSD together bring more than a century of ignition innovation and expertise. The MSDP Group remains committed to leveraging the two brands’ combined resources to keep igniting their loyal customers.

Your Performance Corner retailer will be happy to help you find your favorite ignition part. Find your closest affiliated store using our dealer locator.

If you are a performance aftermarket retailer who would like to become part of the nationwide Performance Corner network, please join us today!

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.