Hurst (6130010): Stage One Spring Kit for ’11-’16 Challenger R/T & SRT8

The Stage One Spring Kit from Hurst is a terrific way to firm up your car’s handling and give it that “just right” stance. These springs will lower your vehicle approximately 1 inch when installed, closing up that fender gap, lowering your car’s center of gravity for improved handling and braking, and enhancing overall driving feel—all while remaining street friendly thanks to its careful design and rate tailoring. Keep it firm; keep it low; keep it Hurst.

Features

  • High-performance handling.
  • Just-right stance for the perfect muscle-car look.
  • Daily-driver/street friendly.
  • Lower center of gravity (will lower your vehicle ~1”).
Hurst (6130010): Stage One Spring Kit for ’11-’16 Challenger R/T & SRT8
Hurst (6130010): Stage One Spring Kit for ’11-’16 Challenger R/T & SRT8

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.

Hooker (71222008HKR): GM A-body LS Swap Transmission Crossmember

Hooker, a leader in LS engine swaps, has announced a new Transmission Crossmember for 1964–1967 GM A-Body—available now! Its bolt-in design makes installation a snap, provides excellent ground clearance, and optimizes driveline angles. Designed for use with Hooker 71221008HKR or 71221009HKR 1964-67 A-body LS engine brackets to optimize U-joint working angles.

Features

  • High-strength/low-alloy steel construction for to balance strength, stiffness weight, and cost.
  • Modular design allows for direct installation of T56/T56 Magnum and 4L80/4L85 transmissions in any non-boxed frame 1964–1967 A-body vehicle.
  • Available add-on transmission adapters.
  • Black powdercoat provides attractive corrosion resistance.
Hooker (71222008HKR): GM A-body LS Swap Transmission Crossmember
Hooker (71222008HKR): GM A-body LS Swap Transmission Crossmember

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.

Edelbrock (2231): Rollin’ Thunder Camshaft for ’57-’86 SB Chevy

Edelbrock (2231): Rollin’ Thunder Camshaft for ’57-’86 SB Chevy

Edelbrock Rollin’ Thunder series camshafts improve horsepower and torque, produce a satisfying performance idle, and provide sufficient vacuum for power brakes and other powered accessories. As with all Rollin’ Thunder camshafts, the 2231 features a more aggressive lift profile than conventional hydraulic flat-tappet cams—without the excessive valve overlap that can compromise low-rpm drivability.

Features

  • Exclusively engineered for 1957–1986 Chevy V8 engines.
  • Designed for optimum power from 1500 to 6500 rpm.
  • Produced 460 hp and 460 ft-lb. torque on an Edelbrock 383 crate engine.
  • Aggressive profile provides excellent performance with sufficient vacuum at idle for power brakes and other powered accessories.
  • 242° intake / 240° exhaust duration at .050″, .594″ lift at valve, and 112° lobe separation.
  • Includes camshaft, assembly lube, and instructions.
Edelbrock (2231): Rollin’ Thunder Camshaft for ’57-’86 SB Chevy
Edelbrock (2231): Rollin’ Thunder Camshaft for ’57-’86 SB Chevy

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.

Holley (550-443): Terminator Stealth EFI Kit with GM Transmission Control

Have you resisted switching to EFI because you like the traditional look of a carburetor? Do you have a GM 4L60/80E transmission in your hotrod? Stop worrying! Holley’s recently released Terminator Stealth throttle body fuel injection system gives you all of the benefits of EFI with the traditional carburetor look you love.

The 550-443 Terminator Stealth EFI system possesses the same great self-tuning features of Holley’s original Terminator EFI in a stealthy new configuration. Holley has made this new system easy to install, with no computer experience required and an included hand-held tuner with multiple-choice setup wizard to get you up and running quickly. Even better, the system self-tunes while you drive, and you can upgrade to complete laptop control without buying another ECU. Available in Polished and Hard Core Gray finishes.

Features

  • Carburetor looks with the drivability of EFI.
  • Trouble-free performance eliminates vapor lock and fuel varnish problems.
  • Fits V8 engines from 250 to 600 horsepower.
  • Fully self-tuning: no laptop required.
  • Full-color, 3.5” LCD touch screen for basic and advanced tuning options.
  • Timing control option for GM Small Cap HEI and Ford TFI distributors.
  • Connections for Ford, GM, TH350, 700R4, and other transmission linkages.
  • Harness for GM electronic 4L60/4L80E transmissions.
  • Optional free software upgrade for full laptop control.
  • Plug-and-play harness with minimal connections.
  • Virtually maintenance free—keeps your vehicle reliable and ready to drive.
Holley (550-443): Terminator Stealth EFI Kit with GM Transmission Control
Holley (550-443): Terminator Stealth EFI Kit with GM Transmission Control

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.

Rugged Ridge (13260.03): C3 Cargo Cover for 2007+ Jeep Wrangler JK

Rugged Ridge (13260.03): C3 Cargo Cover for 2007+ Jeep Wrangler JK

A versatile Jeep deserves versatile accessories. New from Rugged Ridge is the Configurable Cargo Cover (C3) for Jeep Wrangler JK (2007–2016 2D without subwoofer). The patent-pending 13260.03 offers complete protection for the rear cargo area of your Jeep, protecting carpet and plastic trim from damage, scratches, pet claws, dirt, and other debris. This custom-made, functional accessory also creates a resting space for your pet on long trips.

The C3 Cargo Cover is compatible with rear fold and tumble seats, with a water-resistant, flip-out cover flap to keep dirt from falling into the rear tailgate door gap and an integrated front curtain wall to keep items/pets from entering the front seat area. This product’s unique side retention system ensures that the cover stays in place as you load and unload. Easily installed and removed, Rugged Ridge’s C3 Cargo Cover gives you protection when and where you need it.

Features

  • For Jeep Wrangler JK (2007–2016 2D without subwoofer; 2015–2016 2D with subwoofer).
  • Protects carpet and plastic trim from damage.
  • Creates a safe, restful space for pets on long road trips.
  • Limitable access to front seat area.
  • Compatible with rear fold and tumble seats.
Rugged Ridge (13260.03): C3 Cargo Cover for 2007+ Jeep Wrangler JK
Rugged Ridge (13260.03): C3 Cargo Cover for 2007+ Jeep Wrangler JK

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.

CURT (16540): A20 5th Wheel Hitch Head

If you’re looking for smoother, quieter towing for your home away from home, the A20 5th wheel hitch from CURT combines the company’s patented A-series technology with an easier mounting system and the power of a 20K 5th wheel hitch.

The 16540 uses a patented cast yoke to allow for unimpeded head movement plus exceptional trailer stability. A set of poly-torsion inserts suppresses shock loads and reduces excessive noise, while the head features strong interlocking jaws that facilitate free pivoting and swiveling.

A carbide black powdercoat and CURT’s limited lifetime warranty gives you peace of mind against wear, rust, and other towing enemies.

Note: This A20 head unit is a replacement head only. It requires 5th wheel legs or a 5th wheel roller to be installed—components not included in this package.

Features

  • 20,000 lb. capacity (5,000 lb. vertical load); manufacturer capacities apply.
  • Cast yoke with poly-torsion inserts to suppress shock loads and reduce noise.
  • Fully articulating torsion head for controlled coupling and stable towing.
  • High-strength, interlocking jaws fully wrap the kingpin to minimize noise.
  • Polyethylene lube plate eliminates messy grease deposits.
  • Lockable handle self-resets to the ready-to-couple position after uncoupling.
  • Extra-wide head opening for easier coupling.
  • Fast, one-pin head removal.
  • Alignment pegs and easy-access bolts for simple leg-to-body attachment.
  • Three-position coupling indicator is clearly visible from the truck cab.
  • Three height adjustment positions adapt to your unique truck bed.
  • Compatible with kingpin extension boxes, including common pivoting pin boxes.
  • Meets SAE J2638 testing standards.
  • Durable carbide powder-coated finish.
  • Limited lifetime warranty.
CURT (16540): A20 5th Wheel Hitch Head
CURT (16540): A20 5th Wheel Hitch Head

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.

NSF1 Project Jeep Part 15: Rancho 3.5″ Sport Lift Kit & Differential Covers

NSF1 is a project Jeep Wrangler Unlimited being built as a joint venture between two giants in the automotive aftermarket—Total Truck Centers and Performance Corner—to benefit the Navy SEAL Foundation. This video series will highlight the installation, features, and benefits of products donated by sponsoring program manufacturers.

In this video, we take a closer look at the following from Rancho Suspension:

Rancho 3.5″ Lift Kit (RS66110B)

Rancho HD Differential Cover Dana 30 (RS6218)

Rancho HD Differential Cover Dana 44 (RS6209)

Follow the NSF1 project on:

Facebook: https://www.facebook.com/NSF1Jeep
Twitter: https://twitter.com/performancejeep #NSF1 .

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.

B&M (80260): Trick Shift Automatic Transmission Fluid

Originally developed by B&M for racing applications, Trick Shift automatic transmission fluid is now the most popular high-performance fluid on the street too! Not an additive, Trick Shift comprises a scientific blend of foam inhibitors, pressure agents, and shift modifiers that will provide extended transmission life and drastically improve shift feel.

Trick Shift is the easiest way to measurably improve the transmission performance of your vehicle. It works with all automatic transmissions when a firmer shift is desired. Ideal for towing light trucks and RV applications as well (but not recommended for electronic-controlled transmissions).

B&M 80260 contains 1 gallon of Trick Shift fluid.

Features

  • Desirable firmer shift.
  • Ideal for performance street and racing applications.
  • NOT an additive!
B&M (80260): Trick Shift Automatic Transmission Fluid
B&M (80260): Trick Shift Automatic Transmission Fluid

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.

Holley: Finned and Trussed Valley Covers for GM LS Engines

Holley continues to expand its GM LS engine lineup with new aluminum valley pan covers for LS1/LS6 and LS2/LS3/LS7/LSX GM LS engines. Available in either the classic finned design to match Holley’s popular finned line of valve covers or a new trussed design for a race-inspired look.

These covers are either die-cast or billet aluminum to ensure a high-quality, high-detail part. Provisions for factory oil pressure sender are cast or marked on the bottom of the cover. Five different finish options available!

Finish Options

  • Natural Cast (ready for custom paint)
  • Polished
  • Satin Black (with light texture)
  • Factory Orange
  • Gloss Red

Features

  • Aluminum valley pan covers fit LS1/2/3/6/7/X GM LS engines.
  • Available in finned or trussed design.
  • Made from die-cast or billet aluminum.
  • Marked/cast with provisions for factory oil pressure senders.
  • Available October 30, 2016!
Holley: Finned and Trussed Valley Covers for GM LS Engines
Holley: Finned and Trussed Valley Covers for GM LS Engines

Ready to buy? Need help with the install? To find your nearest Performance Corner® affiliate, see our Store Locator. Or join the conversation at the Performance Corner® Facebook page!

Though this is not a paid review, this content has been produced by The AAM Group in support of suppliers with whom it has a business relationship.